आयताकार नलिकाएं और फिटिंग
Plenum Boxes
Plenum with round take-offs are fitted with flange frames made of sheet angles and braced by cross-wise ribbing
#Available Materials: Galvanized, Aluminium, Stainless Steel.
#Thickness: 26 -18 gauge for Galvanized, .032 - .050 gauge for Aluminium, 24-20 gauge for Stainless Steel
#Length: 100mm-5000mm*
#Finishing type: TDF, S&D, Raw
#Inclusive: Bolt & Nuts, TDF Corners, Gasket, C Cleat
End Caps
The end caps stops square duct ends
#Available Materials: Galvanized, Aluminium, Stainless Steel.
#Thickness: 26 -18 gauge for Galvanized, .032 - .050 gauge for Aluminium, 24-20 gauge for Stainless Steel
#Length: 100mm-5000mm*
#Finishing type: TDF, S&D, Raw
#Inclusive: Bolt & Nuts, TDF Corners, Gasket
Rectangular Take Off
The Take-off fittings are provided based on branches being used. Different finishing type are being used in both sides for easy installation
#Available Materials: Galvanized, Aluminium, Stainless Steel.
#Thickness: 26 -18 gauge for Galvanized, .032 - .050 gauge for Aluminium, 24-20 gauge for Stainless Steel
#Length: 100mm-5000mm*
#Finishing type: TDF, S&D, Raw(Can be on both side or Single sided)
#Inclusive: Bolt & Nuts, TDF Corners, Gasket, C Cleat
L-Panels
The L Panels are beaded in regular intervals to provide strength to for large duct size.
#Available Materials: Galvanized, Aluminium, Stainless Steel.
#Thickness: 26 -18 gauge for Galvanized, .032 - .050 gauge for Aluminium, 24-20 gauge for Stainless Steel
#Length: 100mm-5000mm*
#Finishing type: TDF, S&D, Raw
#Inclusive: Bolt & Nuts, TDF Corners(provided separately), Gasket, C Cleat
Rectangular WYE branch
The wye tees are fitted with sheet angles, and the entire fitting is braced by cross-wise ribbing. This fitting allows building the duct work with two take-offs set at any angle.
#Available Materials: Galvanized, Aluminium, Stainless Steel.
#Thickness: 26 -18 gauge for Galvanized, .032 - .050 gauge for Aluminium, 24-20 gauge for Stainless Steel
#Length: 100mm-5000mm*
#Finishing type: TDF, S&D, Raw
#Inclusive: Bolt & Nuts, TDF Corners, Gasket, C Cleat
# The width may vary between the two take-off ports
Rectangular TEE Elbow
T-pieces with take-off bends are fitted with flange frames made of sheet angles and braced by cross-wise ribbing
#Available Materials: Galvanized, Aluminium, Stainless Steel.
#Thickness: 26 -18 gauge for Galvanized, .032 - .050 gauge for Aluminium, 24-20 gauge for Stainless Steel
#Length: 100mm-5000mm*
#Finishing type: TDF, S&D, Raw
#Inclusive: Bolt & Nuts, TDF Corners, Gasket, C Cleat
#Angle Available: 90°,45°,30°
Rectangular TEE fitting
The T-piece ends are fitted with sheet angles, and the entire fitting is braced by cross-wise ribbing
#Available Materials: Galvanized, Aluminium, Stainless Steel.
#Thickness: 26 -18 gauge for Galvanized, .032 - .050 gauge for Aluminium, 24-20 gauge for Stainless Steel
#Length: 100mm-5000mm*
#Finishing type: TDF, S&D, Raw
#Inclusive: Bolt & Nuts, TDF Corners, Gasket, C Cleat
Rectangular Tapper
The eccentric/concentric reducers are adapters designed for coupling two rectangular ducts of different sizes
#Available Materials: Galvanized, Aluminium, Stainless Steel.
#Thickness: 26 -18 gauge for Galvanized, .032 - .050 gauge for Aluminium, 24-20 gauge for Stainless Steel
#Length: 100mm-5000mm*
#Finishing type: TDF, S&D, Raw
#Inclusive: Bolt & Nuts, TDF Corners, Gasket, C Cleat
Rectangular Offsets
Offsets help bypassing obstacles along the duct work route, i.e. at intersections of two ducts.
#Available Materials: Galvanized, Aluminium, Stainless Steel.
#Thickness: 26 -18 gauge for Galvanized, .032 - .050 gauge for Aluminium, 24-20 gauge for Stainless Steel
#Length: 100mm-5000mm*
#Finishing type: TDF, S&D, Raw
#Inclusive: Bolt & Nuts, TDF Corners, Gasket, C Cleat
Rectangular Radius Elbow
The 90˚ elbows are fitted with sheet angles, and the entire product is braced by cross-wise ribbing.
#Available Materials: Galvanized, Aluminium, Stainless Steel.
#Thickness: 26 -18 gauge for Galvanized, .032 - .050 gauge for Aluminium, 24-20 gauge for Stainless Steel
#Length: 100mm-5000mm*
#Finishing type: TDF, S&D, Raw
#Inclusive: Bolt & Nuts, TDF Corners, Gasket, C Cleat
#Angle Available: 90°,45°,30°
Rectangular Straigth Ducts
All rectangular ducts are fitted with flange frames made of sheet angles and braced by cross-wise ribbing.
#Available Materials: Galvanized, Aluminium, Stainless Steel.
#Thickness: 26 -18 gauge for Galvanized, .032 - .050 gauge for Aluminium, 24-20 gauge for Stainless Steel
#Length: 100mm-5000mm*
#Finishing type: TDF, S&D, Raw
#Inclusive: Bolt & Nuts, TDF Corners, Gasket, C Cleat